【Pre-Order】Mini Heater
- Intelligent Temperature Control for Hassle-Free Printing
- PTC Rapid Heating, Ultimate Speed & Efficiency
- 10,000R/Min High-Speed Fan Enables Rapid Heat Transfer
- Real-time Temperature Feedback, Printing In Your Hands
- Fresh Workspace, Assured By Air Filtration
Estimated Shipping Time from AU Warehouse - October 18th.
Where We Ship
Orders placed on the ELEGOO AU website can be shipped to Australia.
The estimated delivery time for in-stock products is 3-7 workdays.
If you pre-order a product, it will be shipped according to the estimated delivery time mentioned on the product page, and after shipment, it takes 3-7 workdays for delivery.
*Please note that the ELEGOO AU website does not currently ship to New Zealand.
Shipping Restrictions
Unable to ship the Jupiter and Jupiter SE 3D printer to post office addresses.
You may only ship to one address per order. If your order contains items that require shipping to multiple locations, you’ll need to place separate orders for each address.
Shipping Fees:
For orders over $70 AUD, it’s FREE SHIPPING. Orders under $70 AUD will be charged a $20 AUD shipping fee. EXCEPT for the conditions listed below:
- For orders including Jupiter SE, some areas (Northern Territory, Queensland, Tasmania, Western Australia) will be charged shipping fees.
- For orders including Saturn 4 or Saturn 4 Ultra will be charged $30/pc shipping fees.
Ownership, Terms, and Risk
Please ensure your address details are correct as once the parcel is on its way we cannot re-direct it. It is your responsibility to check and verify. Should any loss be incurred due to the input of an incorrect address or a fraudulent transaction, you will be held responsible as the sole bearer of the pecuniary loss.
Note: Please do not enter any PO Box address for orders containing Jupiter SE, otherwise, your package can’t be dispatched by any express.
Normally the orders that have been shipped out (you have received the tracking number or your order status has been completed) cannot be canceled. If you have to refuse delivery due to force majeure after the package is dispatched from ELEGOO, you are subject to the return and refund policies and must pay for the original shipping charges, which will be deducted from your refund.
If you do not contact the delivery company within 5 days after the delivery attempt, they may return the goods to us. A return charge may be assigned to us which may be twice of the delivery cost. If the case of this happens, we reserve the right to ask you to pay the return charge plus an additional re-delivery cost before we re-dispatch the item to you.
When the goods are delivered, please check that the order is complete and undamaged. If there is any damage to the goods at the point of delivery, you can contact us: info@elegoo.com
Following a successful transaction you will be notified when your order has been dispatched with a tracking number provided, if you do not receive a tracking number within 48 hours of completing your purchase, we ask that you first check your email “Junk/Spam” folder and then contact us: info@elegoo.com
Refund Policy & Warranty Info
Thank you for your purchase. We hope you are happy with your purchase. However, if you are not completely satisfied with your purchase for any reason, ELEGOO provides a straightforward warranty that is processed in the most hassle-free way possible. Please refer to the warranty policy below, as warranty periods and warranty rules differ according to the models and parts list.
Warranty Policy
1. Warranty timeline
Models | Parts List | Warranty Period | |
3D Printing Related Products | Neptune 3 Neptune 3 Pro/3 Plus/3 Max Neptune 4/4 Pro/4 Plus/4 Max OrangeStorm Giga |
PEI Platform Plate, Nozzle, Heater, Thermistor, PTFE Tube, Tools | No warranty |
Hot End | 3 Months | ||
Extruder Kit | 6 Months | ||
Main Parts of the Machine | 12 Months | ||
Jupiter | Release Film, Tools | No warranty | |
LCD Screen | 3 Months | ||
Resin Tank, Build Plate | 6 Months | ||
Other Main Parts of the Machine | 12 Months | ||
Mars 2/2 Pro/3/3 Pro/4/4 MAX/4 DLP/4 Ultra/5/5 Ultra Saturn S/Saturn 2/Saturn 8K/3/3 Ultra/4/4 Ultra Jupiter SE |
Release Film, Tools | No warranty | |
LCD Screen, Resin Tank, Build Plate | 6 Months | ||
Other Main Parts of the Machine (FEP&Tools Excluded) | 12 Months | ||
Mercury Mercury Plus V1.0/V2.0 Mercury X/XS Bundle |
Main Parts of the Machine (Tools Excluded) | 12 Months | |
PHECDA LASER ENGRAVER & CUTTER- 10w/20W |
Main Parts | PCB, Motor, Laser head, Power Adapter | 12 Months |
Other Parts① | Fans | 6 Months | |
Other Parts② | Synchronous belt, motor connection line, laser connection line | 3 Months | |
Consumables and Other attached |
Power cord, USB cable, Engraving Material (filter cartridge, wood board, stainless steel sheet, leather, etc.), user manual, packaging, tools (hexagonal wrench, open-end wrench), etc. | No warranty | |
Arduino Kits, Robot Kits & Component Kits | All | All | 12 Months |
Pre-owned Products | All | All | No warranty |
Accessories (For individual purchases) | Release Film:FEP/PFA/ACF | Release film is a consumable product without warranty | No warranty |
LCD Screen: Mars/Jupiter |
Resin leakage, scratch-resistant film damage, human damage, collision damage are not included in the warranty. | 3 Months | |
LCD Screen: Mars 2/2 Pro/3/3 Pro/4/4 Ultra/4 Max/Saturn /S/2/8K/3/3 Ultra/4/4 Ultra/Jupiter SE |
Resin leakage, scratch-resistant film damage, human damage, collision damage are not included in the warranty. | 6 Months | |
Build Plate | Damage caused by scratches, drops or bumps is not covered by the warranty. | 6 Months | |
Resin Tank | Installation tools and screws are not warranted | 6 Months | |
Air Purifier: Mini/USB/Mars Mate |
Consumables (activated carbon) are not warranted, as well as human damage, disassembly is not covered by the warranty. | 12 Months | |
Mini Heater | Consumables (activated carbon) are not warranted, as well as human damage, disassembly is not covered by the warranty. | 12 Months | |
Washing Bucket:Mercury Plus V1.0/ V2.0Mercury X/XS Bundle | No warranty for damage caused by man / misuse (e.g. resin curing inside the bucket). | 6 Months | |
3D Stainless Steel Funnel | 3D Stainless Steel Funnel is a consumable product without warranty | No warranty | |
PEI Platform Kit/PEI Magnetic Platform Kit | PEI Platform Kit is a consumable product without warranty | No warranty | |
Nozzle Kit | Nozzle Kit is a consumable product without warranty | No warranty | |
PTFE Tube | PTFE Tube is a consumable product without warranty | No warranty | |
Hotend Kit | Hotend Kit (Nozzle, PTFE Tube Excluded) | 3 Months | |
Extruder Kit/Printhead Kit | Entire Dual-Gear Direct Extruder Kit | 6 Months | |
Cooling Fan Kit | Including 4010/4015 Blower Fan and 6010 Axial Flow Fan | 12 Months | |
STM 32-bit Silent Motherboard | Motherboard | 12 Months | |
Enclosure | All | 12 Months | |
Dual Printhead Mounting Plate | All | 12 Months | |
Four-Printhead Mounting Plate | All | 12 Months | |
5KG Large Spool Holder Kit | All | 12 Months | |
Camera | All | 12 Months | |
Filament Vacuum Storage Bags Kit | The pump is guaranteed for 1 month and the vacuum bag is a consumable product without warranty. | 1 Month | |
Rotary Attachment: PHECDA Laser Engraver |
All | 12 Months | |
10W/20W Air Assist:PHECDA Laser Engraver | All | 12 Months | |
Enclosure:PHECDA Laser Engraver | All | 12 Months | |
Honeycomb Panel: PHECDA Laser Engraver |
Honeycomb Panel is a consumable product without warranty | No warranty | |
Raisers:PHECDA Laser Engraver | All | 12 Months | |
Composite Filter:PHECDA Laser Engraver | Composite Filter is a consumable product without warranty | No warranty | |
10W/20W Laser Module:PHECDA Laser Engraver | All | 12 Months | |
Window Mirror:PHECDA Laser Engraver | Window Mirror is a consumable product without warranty | No warranty | |
20W Adapter:PHECDA Laser Engraver | All | 12 Months |
2. Warranty Rules for Laser Head and Tube
A. Laser Head WarrantyRules:
The rate of laser power drop is related to the frequency of use, working hours, and working environment.
B. Laser Tube Warranty Rules:
a). If the laser tube is found to be damaged during the first unpacking inspection, after-sales warranty service can be provided normally;
b). During the warranty period, if the laser tube cannot emit light normally, but no obvious appearance defects are found, after-sales warranty services can be provided normally;
c). During the warranty period, if the laser tube has any appearance cracks (including but not limited to cracks caused by improper handling or cracks caused by freezing temperatures), after-sales warranty services can't be provided normally.
3. Warranty Period
All times shown on this page are calculated from the date the original order was received. If you receive free replacement products or accessories, the warranty period will still be calculated from the date the original order was received.
4. Warranty Forfeiture
The following Conditions Are Not Covered Under Warranty:
A. Products without sufficient proof of purchase
B. Lost or stolen products
C. Items that have expired their warranty period
D. Non-quality-related issues (after 30 days of purchase)
E. Free products
F. Repairs through 3rd parties
G. Damage from outside sources
H. Damage from misuse of products (including, but not limited to: falls, extreme temperatures, water, and operating devices improperly)
I. Purchases from illegitimate resourcesor second-handed parties
J. Normal discoloration, wear, or consumption during product use.
Return & Refund Policy
1. For Unwanted Items
*This clause does not apply to Pre-owned & Refurbished items.
If the Elegoo product that you purchased does not meet your satisfaction but was not confirmed defective by certified Elegoo technicians, we call such product as “unwanted product”.
- For products in condition unopened (all original tags and labels attached), within 14 days of delivery, you may return them with an "unwanted reason" and get a refund. You are responsible for the shipping fees, and ELEGOO will charge a 5% restocking fee based on the order amount.
- For products in condition open-box and unused, within 14 days of delivery, you may return them with an "unwanted reason" and get a refund. You are responsible for the shipping fees, and ELEGOO will charge a 15% restocking fee based on the order amount.
- For used products or orders beyond 14 days, refunds for unwanted products are not available.
Unwanted Issue |
|||||
|
Product Status |
Items |
Responsibility of Return Shipping Charges |
Restocking Fee |
Deduction Fee |
Refund |
|||||
Within 14 Days |
Unopened |
√ |
Customer |
5% based on the order amount |
If the returned machine detects key parts missing, the corresponding fees will be deducted. |
Open-box and unused |
√ |
Customer |
15% based on the order amount |
||
Used |
× |
× |
× |
||
Within Warranty |
All Status |
× |
× |
× |
× |
Important: After receiving the goods, please keep the original box for at least 14 days. If you need to return the goods, you must pack the products in the original box.
For your own benefit, we recommend that you use a traceable carrier that can provide you with the delivery confirmation to ship your Product for refund back to the location instructed in the RMA authorization. Elegoo shall not be responsible for any loss or damage to the returning product caused in transit.
The returning product will be thoroughly inspected by Elegoo when received and a decision will be made whether the inspection criteria are met. If your returning product fails to satisfy the inspection criteria and has been shipped to Elegoo, your non-conforming product for refund will be rejected or subject to a deduction fee at Elegoo’s sole discretion.
After the 14-day refund window has expired, your only recourse regarding the products is through our warranty.
2. For Quality-Related Items
*This clause does not apply to Pre-owned & Refurbished items.
A. Product is defective when you receive it, within 14days of delivery, you can return defective items to Elegoo and get a full refund or replacement, and Elegoo is responsible for return shipping charges. Or you can ask Elegoo to repair defective items, and Elegoo is responsible for repair fees.
B. Beyond the 14days but within warranty, a full refund and replacement are not available, but repair is acceptable. Elegoo is responsible for repair fees.
C. Out of warranty, Elegoo will provide free technical support, if the parts need to be replaced, the customer is responsible for the repair fees, which means the customer needs to purchase the parts and bear the freight.
Quality-Related Issue |
|||||
|
Items |
Responsibility of Fees |
|||
Refund |
Replace |
Repair |
Return Shipping Charges |
Repair Fees |
|
Within 14 Days |
√ |
√ |
√ |
Elegoo |
Elegoo |
Within Warranty |
× |
× |
√ |
× |
Elegoo |
Out of Warranty |
× |
× |
√ |
× |
Customer |
Important: 1. After receiving the goods, please keep the original box for at least 14 days. If you need to return the goods, you must pack the products in the original box.
2. To avoid any delay or denial of processing your refund and replacement request, please verify that the returning product must be with all parts & accessories included and all original tags and labels attached and in the original box (generic boxes will be rejected).
3. Process After Returning Product
After receiving your return and inspecting the condition of your item, we will process your return. Please allow at least 7 days from the receipt of your item to process your return. We will notify you by email when your return has been processed and move to the next warranty process, refund you the payment via Paypal, or send a new replacement to you.
Contact Us
Regarding product issues, please don't hesitate to contact us at the customer service channels below to acquire technical support, refund or exchange.
- For 3D printer technical support: 3dp@elegoo.com
- For laser engraver technical support: lec@elegoo.com
- For order issues, unwanted item refunds, or returns: info@elegoo.com
- For STEM kits, robots technical support: service@elegoo.com
When contacting our customer service team, the buyer must provide sufficient proof of purchase (the order number from online purchases made through ELEGOO, Amazon, or other ELEGOO's authorized resellers), tell us which product you purchased, and describe the problem as clearly as possible through text, images or short videos. This will help our team to process your inquiries and help you solve the problems more efficiently.
Intelligent Temperature Control for Hassle-Free Printing
The Mini Heater features precise and intelligent temperature control, ensuring optimal stability from start to finish. Say goodbye to frustrating issues like mid-print detachment, warping, and poor interlayer adhesion that hinder your progress.
Forget about manual adjustments and temperature fluctuations. The Mini Heater's automatic heating function intelligently engages below 25℃ and disengages above 25℃, guaranteeing continuous heat optimization. Focus on your creativity as the intelligent temperature control takes care of the rest.
PTC Rapid Heating, Ultimate Speed & Efficiency
Experience the power of swift and efficient printing with the Mini Heater's advanced PTC heating technology. Watch in awe as the chamber temperature rapidly rises to 25°C, allowing you to dive into your printing projects with unprecedented speed.
But that's not all. Combined with its 120W ultra-high power, the Mini Heater can also achieve exceptional energy efficiency by reducing power consumption without compromising heating performance. Plus, with the PTC element's self-regulating properties, you can rest easy knowing that overheating is prevented, providing enhanced safety throughout operation.
10,000R/Min High-Speed Fan Enables Rapid Heat Transfer
Equipped with a 10,000R/Min high-speed fan, the Mini Heater provides optimal airflow and efficient, even heat distribution, eliminating hotspots and maintaining a consistent temperature, which ensures uniform melting and deposition of the print material for remarkable print quality.
Real-time Temperature Feedback, Printing In Your Hands
Stay informed and in control of your printer's temperature with real-time updates, enabling you to promptly detect and troubleshoot temperature-related issues, and ensuring optimal performance at all times.
Fresh Workspace, Assured By Air Filtration
Embrace the combination of cleanliness and precision with the Mini Heater, which incorporates an efficient air filtration system, allowing to remove impurities and ensure a clean and purified printer chamber.
Effortless Installation For Smooth Start
The Mini Heater features a user-friendly design, ensuring a seamless and enjoyable experience from unboxing to printing your first masterpiece. With its straightforward installation process, you can easily set it up and embark on your printing journey with confidence.
High Compatibility For Seamless Integration
From the latest cutting-edge releases to the trusted older versions, the Mini Heater is designed to seamlessly integrate with a wide range of ELEGOO printers, including Mars 5 Ultra, Mars 5, Mars 4 Max, Mars 4 DLP, Saturn 4, Saturn 4 Ultra, Saturn 3, Saturn 3 Ultra, Saturn 2, Saturn 8K, Saturn S and Jupiter SE.
Not limited to ELEGOO printers, the Mini Heater can also be easily adapted to work with printers from other brands. Simply refer to the adapter plate's size map and manually add the required perforations to your printer for a hassle-free integration of the Mini Heater.
① Air Outlet
② Real-time Temperature Display
③ Operation Indicator Light
④ Power Switch
⑤ Power Interface
⑥ Filter Compartment
Installation and Usage Instructions
Follow the diagram to properly attach the adapter plate to the printer's casing using the screws provided in the tool kit (only install the diagonal screws on the top left and bottom right).