Skip to content
What Is Infill in 3D Printing? Density, Patterns, and Walls

What Is Infill in 3D Printing? Density, Patterns, and Walls

Infill is the structure a filament printer builds inside a part’s walls. It lets the part have a useful interior without turning every model into a solid block of plastic. Change its density or pattern, and you change how that space is filled.

If you’ve just opened a slicer for your 3D printer, the percentage can look like a strength dial. It isn’t that simple. A tidy desk organiser, a display model and a bracket each ask something different of their walls and interior. Here’s how to choose a sensible starting point—and what to inspect before pressing Print.

Table of contents
  1. Look inside the part first
  2. What does the infill percentage mean?
  3. Choose a starting point for what you’re making
  4. Which infill pattern should you use?
  5. Check the walls and top layers before adding more infill
  6. Try a controlled comparison in your slicer
  7. When a different approach makes sense
  8. Frequently asked questions

Look inside the part first

Imagine a closed box printed as one piece. The side walls form its boundary, the bottom layers give it a floor, and the top layers close it. Infill occupies the space between them and gives those upper layers something to build across.

WallsPaths around the model’s outline, including boundaries around designed holes.
Top and bottom shellsSolid layers that close the part where the model has a surface.
Sparse infillThe lighter internal structure between those surfaces.
Exposed grid infill and perimeter walls inside an unfinished filament print.
The outer walls and internal grid are visible in this example from our troubleshooting library. The irregular strands are a print defect, not the intended finish of a well-printed infill pattern.

You usually let the slicer generate this structure. You don’t need to draw every internal line in CAD. A hole or open compartment that belongs to the model stays part of its geometry; increasing infill does not fill in the opening of a correctly modelled pen cup.

What does the infill percentage mean?

The percentage controls the intended density of the sparse interior. At a lower setting, the structure leaves more open space. At a higher setting, it places more material within that region. The resulting mass also depends on the pattern and how much room remains after the walls and solid layers are generated.

20% infill does not mean the finished object weighs 20% of a solid version. Its walls, top and bottom still use material. A thin part may be made mostly of walls, leaving very little space for sparse infill at all. Compare the slicer’s material estimate to see the effect on your actual model.

Likewise, moving from 10% to 20% does not double the strength or the total print time. It changes one part of a larger structure.

Choose a starting point for what you’re making

The ELEGOO Slicer V2.1 manual gives 15–20% sparse infill as a general starting range for supporting model structures. Use that as somewhere to begin with an ordinary, noncritical print, then check the geometry and the result. It is not a load rating.

Your project A useful first choice Check before committing
A display model Try the profile’s ordinary infill first; compare a lower-density or lightning option if weight matters. Can the internal structure support the first solid top layers?
A desk organiser Start around 15–20% where the model has an interior to fill. Are the base and dividers thick enough for daily handling?
A fit-check prototype Keep the dimensions and surfaces you need to assess; use only enough interior support to print them. Will a lighter sample still answer the fit question?
A working bracket or fixture Choose material and orientation first, then compare wall and infill changes. Test the actual geometry under its intended load. A percentage alone cannot establish suitability.
A lithophane or other special model Follow the model-specific instructions. Some designs need a dense interior for appearance or another purpose.

There’s no prize for using the highest percentage. Once the print does its job reliably, an extra-heavy interior may simply be something you paid and waited for.

Which infill pattern should you use?

The pattern describes how the material is arranged. Availability and exact behavior vary by slicer, so compare the preview rather than assuming identically named settings produce identical paths.

Pattern What you’ll see A reason to consider it
Rectilinear Straight lines, with direction changing between layers A straightforward baseline for comparing time and top-surface support
Grid Crossing lines within a layer An easy-to-read internal network; crossings can accumulate material, so inspect scraping or rough intersections
Gyroid Wavy paths forming a structure through successive layers A candidate when the part needs support in several directions; not a guarantee of equal strength in the finished part
Cubic A repeating three-dimensional cell structure Another candidate to compare for a functional prototype
Lightning Branches concentrated beneath upper surfaces Reducing material in suitable display models; it is not general reinforcement throughout the whole interior

Keep the model, orientation and other settings unchanged when comparing two patterns. Look at both estimated material and time. The quickest option for one shape may not be the quickest for another.

Check the walls and top layers before adding more infill

If a part bends or cracks, look at where it happens. A thin outside edge, an unsuitable material or weak bonding between layers calls for a different response from an unsupported top surface. More plastic in the centre cannot fix every one of those problems.

On an FDM 3D printer, wall count controls the number of perimeter paths. Actual wall thickness also depends on extrusion width and the slicer’s path generation. Check the preview rather than treating nozzle diameter multiplied by wall count as an exact measurement.

Top layers need enough thickness to close cleanly over the internal pattern. As a simple constant-layer-height example, four layers at 0.20 mm give 0.80 mm of nominal thickness; four at 0.10 mm give 0.40 mm. A separate minimum-thickness setting can make the slicer add layers, so check the generated result.

If the top has gaps, inspect its thickness, the span between infill lines and the quality of extrusion. If the outside has a visible internal pattern, inspect the walls and infill connection. Change the setting that addresses the defect instead of increasing several unrelated values at once.

Try a controlled comparison in your slicer

Use a small organiser or another low-risk model you understand. Start with a suitable saved profile and make a baseline slice. Then compare the following versions separately:

  1. Density comparison: keep the pattern and walls fixed; compare 15% and 20% sparse infill.
  2. Wall comparison: return to the baseline; add one wall loop and leave infill unchanged.
  3. Pattern comparison: return to the baseline again; change only the infill pattern.

Record the predicted time, material use and any difference in the layer preview. You may find that adding a wall changes a thin feature much more than adjusting the infill percentage. Those are slicing comparisons, not proof of strength: print and inspect the version appropriate to the part’s use. For scheduling the complete project, see how long 3D printing takes.

Before sending the file, move through the preview from bottom to top. Check that the interior reaches the walls as intended and that the first top layers have support beneath them. Once you have a successful print, save that project as a useful reference for similar work.

When a different approach makes sense

100% can serve a specific purpose

Some designs call for a dense interior for reasons other than strength. Our CMYK lithophane tutorial specifies 100% rectilinear infill for its particular four-colour workflow to avoid unwanted internal gaps affecting the backlit image. Follow the complete tutorial for that project; do not transfer the setting automatically to a bracket or display figure.

A completed backlit flower lithophane shown in the ELEGOO CMYK printing tutorial.
A lithophane uses transmitted light to reveal an image. In this specific workflow, the interior settings help control the visual result.

Resin hollowing needs its own workflow

An LCD 3D printer can also produce hollow parts and, in some slicers, internal filling structures. That does not make FDM density settings interchangeable with resin preparation. You need to account for drainage, access for cleaning and curing, and supports inside the cavity. Our SatelLite hollowing and drainage guide explains the relevant tools.

Frequently asked questions

Is 20% infill strong enough?

It can be a reasonable starting point for an ordinary organiser or display piece. The number does not tell you how much weight a part can carry. Geometry, material, wall thickness, layer bonding and load direction all affect that answer.

Can I print with 0% infill?

Sometimes. The walls and any top and bottom shells remain, but a wide closed roof may have nothing beneath it to support the first solid layer. Check that the geometry can print successfully. Setting 0% infill is also not the same as enabling spiral vase mode.

Is infill the same as support?

No. Sparse infill normally stays inside the finished part. Slicer-generated supports are temporary structures used to help print overhangs and other unsupported areas, then removed. Infill supports the part internally, but it does not replace every external support the model needs.

Which pattern is strongest?

There is no universal winner. A pattern that performs well under one kind of load may not lead under another. Compare the actual part and material, and include wall thickness and print orientation in the evaluation.

Shopping Cart · 0

Your cart is currently empty.

Start Shopping